Year: 2023

Week commencing 3rd July – tour the the west is nearing the end.

Day 5 – Friday – Hapton & Copster Green…

Our first call of the day was over to Hapton, which was a short hop from our digs in Burnley, where it was great to meet Paul for work on his fairly new acquisition of a TF 160 80th anniversary in paint code PBT. Already being an owner of a BRM he had fancied getting a TF. So he eventually came upon this one after a few attempts at buying it at auction.

Full cambelt service carried out for him, plus alternator belt, underfloor stainless coolant pipes replaced as his were a tad rotten. Plus, while we were there, he asked if we could replace all pads and discs as the car had been sat for many year without turning a wheel.

Date to be arranged to replace the wishbones and do a full underfloor treatment.

Brilliant day in Paul’s company chatting while we worked with a constant stream of cuppas!

We’re now in Copster Green, for replacement of two front wheel bearings on Maggy’s ‘Ophelia’, her TF 160 in paint code IAA. Well Jon’s doing that actually, while I’m doing the admin with some very good company. 🐾

The van decided to be a bit naughty and not want to start again when we arrived, but Jon’s worked his magic on that again. It’s a beautiful sunny evening and really lovely as always to see Maggy and Phil. – https://ift.tt/ILquk62

Week commencing 3rd July – tour to the west continues.

Day 4 – Thursday – Skipton & Burnley…

A departure from our digs in Thornley and a run over to Skipton this morning, where it was good to meet Tom, for work on his fairly new acquisition of a ‘98 MGF 1.8 mpi. Since buying the car 4 months ago he’s done a fair few miles and been loving it. Knowing that the cambelt service was due he asked us to come over and carry this out for him and also to do a preemptive head gasket replacement as he just wanted peace of mind and worry free motoring.

It’s actually a good thing that he did, as he would have been having a spot of bother sooner or later. On checking which gasket was fitted, we initially thought it was an elastomer, as there wasn’t a tab sticking out between the block and the head, but when we removed the cylinder head, it was in fact an MLS gasket, but the saver-shim hadn’t been fitted.

At some stage in the past a fairly large amount of the hideous k-seal had been added. The expansion tank was full of it. The inlet manifold was blocked and the return hoses were solid with the stuff, and not the usual thick gungey stuff, it was dried out. So all of these were cleared out, hoses removed then blown and flushed through, using various methods. Poor car!

All missing gaskets and bolts replaced and everything refitted. Car ran up to temperature and behaving as it should.

Tom only had one key fob with the car so a replacement one of these were programmed for him. Thanks to Tom for the cuppas and for the forecast not being as it was supposed to be and dodged the rain.

We now over in Burnley for the night, ready for tomorrow. Good to have time for a walk along the canal. – https://ift.tt/QndGZh7

Week commencing 3rd July – tour to the West of England (whose splitting hairs).

Day 3 – Wednesday – Blackpool…

Our first call was for work on Allen’s MGF 75th Anniversary 120 mpi, in paint code CDM. The cambelt service was due so we carried this out. He had noticed a couple of issues with overheating. On pressure testing and investigating thought it was probably due to the inlet manifold being blocked, sure enough the return valve was completely blocked and the gasket was old. These were cleared and replaced and the car ran up to temperature and holding pressure.

But, on the subsequent test drive the car overheated again. By this time we had only gone 6 miles down the road anyway and almost finishing the second job of the day, which was for a full cambelt service on Dave’s ‘05 TF 135 in paint code LEF.

Dave’s very low mileage TF was almost like new, so all bolts etc came off easily. Cambelt, water pump, tensioner, all filters and oil replaced. It was lovely to meet Dave, who welcomed us with a cuppa. The car will be going up for sale sometime soon. After a chat with him we bid our farewells and headed back along the road. We wish him well with the sale of the car.

Once back at Allen’s we set about replacing the head gasket. With only one awkward exhaust manifold bolt the car was put back to rights and up and running lovely.

A real pleasure to meet Allen and have a chat while we worked this morning and this afternoon!

Two very nice examples today, great company and the bonus of the sun making an appearance.

We’re now in our next lodgings near Longridge, just made it in time to order some tea. One night here, and then we head to our next destination in the morning, Skipton. – https://ift.tt/QndGZh7

Week commencing 3rd July – tour to the West of England.

Day 2 – Tuesday – Wirral & Wilmslow…

Our first call took us from our digs in Chester over to Wirral, where it was really lovely to meet Samantha for work on her ‘96 MGF 1.8 mpi that her husband, Andy, bought for her, earlier in the year, but it came with no service history.

This morning we carried out a full cambelt service. What a good honest car, with all
original features, they had even got hold
of some cassettes to play in it, so fab! It had been dry stored and sat for many years prior to them taking ownership. So it now has a new lease of life and will be used for fun outings.

From there we headed over to Wilmslow for work on John’s, also fairly new acquisition, ‘04 TF 135 in paint code JFM. He’d bought the car knowing it had potential issues with the head gasket, so had it transported home, as didn’t want to risk running it.

Sure enough, all the signs were there, and on removing the cylinder head it had been fitted with an elastomer gasket and had gone into cylinders 3 & 4. All gaskets replaced and the car is now back up and running lovely. John was so pleased to hear it spark into life. He’ll take it for the MOT and then get out and about and have some fun over the summer on his retirement.

Really great to meet him and have a chat while we worked, accompanied by many cuppas, he’d read that bit about us!

We managed to dodge the forecasted bad weather, with only one small shower. So, all in all a busy one, but a really pleasant days work.

We bid our farewells and are now in Altrincham for the night, before heading over to Blackpool in the morning. – https://ift.tt/2RALEnb

Week commencing 3rd July – tour to the west of England.

Day 1 – Weaverham & Birkenhead…

On a very very wet Monday morning it was nonetheless good to meet Layton for work on his ‘02 MG TF 135 in paint code JFV.

Head gasket replacement, cambelt service, underfloor coolant pipes replaced, plus a couple of other bits. On running the car up to temperature we found no return to the expansion tank, so we flushed through a lot of solidified gunk in the return hoses from over the gearbox. Happily the car is now back up and running as it should be.

Thankfully, the gazebo sheltered us from the majority of the torrential and continuous downpour, but still a bit soggy and cold, and guess what, the sun came out just as we were packing up! Big thanks to Layton for lots of cuppas.

From there we went over to Birkenhead for investigation on a problem Mark had been experiencing with his MGF 1.8 120 mpi for about a year, he had gone through all of the usual suspects, replacing parts, some on a couple or more times, only to have the same problem reoccur.

Hooked up the diagnostics, only a single error code coming up, which is known to be false anyway, set about checking all the ignition system, coil pack, the distributor, HT leads and plugs, found the distributor cap had a loose central core, replaced that, replaced one of the plugs as the porcelain was cracked, but still the same result.

Checked the wiring for the throttle body, tried various different throttle bodies, still no joy. The only thing left was that the diagnostic had shown on live data that zero volts were coming back on the Lambda sensor, even though Mark had replaced with a Bosch sensor.

We temporarily fitted another one to make sure it wasn’t just the cabling, this showed .44 volts on live data, so the sensor that was fitted was faulty.

We also noticed that the throttle body was permanently showing open-loop, which it should be closed-loop on tick-over. Finally the manifold air-pressure was static all the time at 99 Kpa.

It would come down to possibly being the ECU and a faulty Lambda. Mark will source a replacement ECU and then go from there.

Bit of a head scratcher, shame not to be able to fix it on one visit, but we will keep in touch and see what progress he makes with this other information. It was although, great to meet Mark and have some interesting chats.

Bit of a late finish and a long day, but we’re now in our digs near Chester, I’m on the admin and Jon’s going to order his delectable delights from Just-Eat. – https://ift.tt/2RALEnb

Darlington and Stockton-on-Tees today…

Our first call of the day was in Darlington, where it was great to meet Alex for work on his ‘96 MGF 1.8 mpi in paint code HAM.

Unfortunately, the head gasket, having fairly recently been replaced by another company, had gone again, due to a faulty ECU temperature sensor. The sensor was reading too low, allowing the car to boil over before it had attempted to put the radiator fan on, this was most likely the cause of the first failure.

All gaskets replaced, and new ECU temperature sensor and the temperature gauge sensor both replaced with new. We’re so pleased for Alex that the car is now up and running for him as it should be.

Lovely to meet him and have interesting chats while we worked, along with many welcome cups of tea. It was great to hear from him later on after a run out that the car is running lovely and smooth.

From there we headed over to Billingham where it was lovely as always to see Gary, Liam and Claire. Their TF 135 was due for the annual service and a couple of other bits. Service carried out, and a new key fob programmed, as the one they had was being temperamental. Jon pointed Liam in the right direction for replacing the track-rod-end on one of the fronts. His apprenticeship at Porsch is going really well we’re pleased to hear. He had recently replaced the calipers, discs and pads on ‘Madam’.

Good to have a chat and a catch-up before we left to head off home. Now on the A19, it’s a beautiful evening following a really good day and now it’s admin time! Then tomorrow is unpack the van day from our recent trip and restock it all again to head over the Lancashire etc for the week first thing on Monday morning. – https://ift.tt/XTr7FRe

Days 9 & 10 – Banbury, Worcester & Pershore…

We drove up from our digs yesterday morning to arrive in Banbury for work on Gary’s ‘04 TF 135 in paint code MBB.

Having recently bought the car earlier in the year it came with no service history. So Gary got on with carrying out the minor service and replacing the underfloor pipes and he asked if we could come over to do the cambelt service. Plus we replaced the gearbox oil and flushed through the brake fluid.

Really great to meet him, and his colleague, and have a chat before we went on our way. We were only staying fairly local last night in Wroxton.

This morning we headed further north to our first call of the day in Worcester, where it was really lovely to see Tim for work on his LE 500 in paint code 106 and number 494/500.

Tim had noticed that the wishbones were starting to look a bit flaky and a small hole had appeared in one of them. So these were replaced for him, without any drama of snapping off subframe bolts we were very pleased about! Minor service also carried out for him.

Great to have a chat while we worked, and thanks to Tim for the supply of beverages and biscuits. Hope to see him at a show or an event some time in the coming weeks.

From there we headed over to Pershore, where it was great to meet Richard for work on his ‘99 MGF 1.8 mpi. Richard had noticed oil leaks from both of the drive shaft oil seals. So these were duly removed and replaced with new ones for him.

We’re now heading back home, after 10 nights away and a total of 964 miles, looking forward to seeing the cat. It’s been a successful trip, great to see some old faces and to meet some new ones too. Plus the added benefit of mostly decent weather. ⛅️ – https://ift.tt/nKXY0zl

Days 7 & 8 – Around & About & Liskeard…

A day off yesterday for some much needed R&R and in lieu of our wedding anniversary tomorrow.

This morning, Tuesday, we made a reluctant departure from our absolutely fantastic digs we’ve been in for the past 4 nights, and started to head back up the country, with our destination being Liskeard.

It was good to meet Ray for work on his ‘02 TF 160 Sprint, in paint code MBB.

Full cambelt service carried out for him, plus gearbox oil change. We had to resort to plan B, as the engine mount bolts were definitely not coming undone, which proved successful, thankfully. A few missing and wrong bolts replaced and she’s all good to go.

We’re now in our digs for one night, as a sort of halfway point, before we head further north to Banbury in the morning. – https://ift.tt/MoGEpQS